490-00 MICRO LINK™ - Xantech

Another miniature IR receiver that features surface mount technology. The 490 has its electronics housed in a brass cylinder. The “business end” of the unit is a small round lens. This small receiver is designed to be placed in very tiny spaces. One example is a small corner of an equipment cabinet. A single, 1/2-inch hole will accommodate the 490. The high sensitivity of this receiver gives you the ability to place the 490 further away from the hand held remote, increasing the placement options you have.

490-00 - Standard version, with mini 3-conductor 7 ft. ribbon cable and separate screw terminal block (supplied).

490-95 Xantech Plasma Friendly Micro-Link IR Receiver

NEW!!The 490-95 is Xantechs newest version of their acclaimed Microlink IR Receviers. Designed to reject interference from Plasma Displays from entering the IR signal line. These Small IR Receivers are intended to be mounted in panels, doors, cabinets, etc. for control of A/V equipment behind closed doors or any IR Repeater System that is in close proximity of a Plasma Display

• Includes interchangeable brass, white and black bezels to match any decor
• Rejects interference from plasma displays, direct sunlight and fluorescent tube lights for accurate IR signal reception
• Small size - only 2.5" deep (64mm) by 3/4" diameter (19mm)
• Quick connect 3.5mm stereo mini-plug on 7 foot cable (2.1mm) for direct connection to Xantech connecting blocks
• Works in normal three-wire mode
• RF grid included for RMI interference reduction
• Requires a 781RG Power Supply (up to seven 490-95's may be powered on the same power supply
• Patent pending

490-KIT MICRO LINK™ - Xantech

Another miniature IR receiver that features surface mount technology. The 490 has its electronics housed in a brass cylinder. The “business end” of the unit is a small round lens. This small receiver is designed to be placed in very tiny spaces. One example is a small corner of an equipment cabinet. A single, 1/2-inch hole will accommodate the 490. The high sensitivity of this receiver gives you the ability to place the 490 further away from the hand held remote, increasing the placement options you have.

490-KIT - MICRO LINKTM KIT - Prepackaged kit includes:
(1) 490-30 Micro Link Receiver (brass bezel)
(1) CB60 Connecting Block
(1) 781RG Power Supply
(4) 283M Blink IR Mouse Emitters

490W-30 - Same as 490-30 except with white bezel.

CB18 Strip-IR™ Parallel Connecting Block from Xantech

• Easily connect all those home run wires from multiple IR receivers to the input terminals of a connecting block.
• High current design (12 amps peak) allows amplifiers rated as high as 500W to be used with the CB18.
• One-in and eight-out or eight-in and one-out capability.
• Nine 4-terminal plug-in connectors on 4-conductor bus.
• Screw terminals handle wire sizes from 24 to 12 gauge.

CB20 One-Zone Connecting Block from Xantech

• Connects two emitter ports and power supply to Xantech IR receivers that use a stereo mini plug.
• 3.5 mm stereo mini jack for quick-connect IR receivers
• Two 3.5 mm mono mini jacks with 470 ohm resistors drive 2 single or 2 dual emitters
• 2.1 mm coaxial power jack
• Requires either the 781RG or 782-00 power supply.

CB60 One-Zone Connecting Block from Xantech

• Connects six emitter ports and power supply to all Xantech IR receivers that use a stereo mini plug.
• 3.5 mm stereo mini jack for quick-connect IR receivers.
• 3.5 mm mono mini emitter ports drive 6 single or 6 dual emitters in parallel.
• Contains a series 100 ohm resistor per emitter port.
• Requires either the 781RG or 782-00 power supply.

IRS232 IR to RS232 Module from Xantech

• Provides IR control of advanced components such as projectors and lighting systems.
• Requires 781RG power supply; RC68+ programmer and Dragon Drop-IR™ programming software.

IR-X10 Lighting Module from Xantech

• Converts specific Dragon Drop-IR™ codes into X10 control signals.
• IR input accepts Xantech IR bus output from any of the Xantech IR receivers; keypads; connecting blocks or controllers.
• X10 RJ11 output jack connects to the X10 power line interface module using the included RJ11-to-RJ11 cable.
• Requires a 781RG power supply and Dragon Drop-IR™ programming software.

MAC1 Mini-Macronizer™ from Xantech

• Has the ability to send IR codes; sequences or macros when triggered by a single RC68+ command.
• Requires Dragon Drop-IR™ for programming and 781RG power supply.
• Eliminates the problem of partial sequence execution from movement of hand-held controllers.
• Cuts down network traffic.