Sensors and Detectors > Environmental Sensors > Temperature & Humidity Sensors
Temperature & Humidity Sensors

Winland Temperature & Humidity Sensors

These Temp & Humidity Alert Solutions provide reliable protection to monitor high and low temperature/humidity limits for residential or commercial property. The Temp Alert and Humid Alert products complement the burglary or fire protection security products sold today.



EnviroAlert EA40012 & EA40024
Monitor four zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor the designated relay for each zone will activate an alarm, dialer, transmitter, etc.
EA400-12 12Volt 4-Zone Enviro Alert Temp Sensor

EA400-12 12Volt 4-Zone Enviro Alert Temp Sensor

Winland Electronics EnviroAlert® Four Zone Digital Environmental Monitoring Alarm (EA400-12 & EA400-24)

Monitor four zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor the designated relay for each zone will activate an alarm, dialer, transmitter, etc.



EA400-24 24-Volt 4-Zone Enviro Alert Temp Sensor

EA400-24 24-Volt 4-Zone Enviro Alert Temp Sensor

Winland Electronics EnviroAlert® Four Zone Digital Environmental Monitoring Alarm (EA400-12 & EA400-24)

Monitor four zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor the designated relay for each zone will activate an alarm, dialer, transmitter, etc.





EnviroAlert EA20012 & EA20024
This advanced monitoring and alarm device provides precise monitoring of critical environments by utilizing an on-board temperature sensor or attaching any one of the remote temperature, humidity and water sensing probes. Receive dual zone coverage from simultaneous operation of the local and remote sensors. If either zone being monitored deviates from the preset limits, a relay output sends a signal to an appropriate warning system.
EA200-12 Enviro Alert 2-Zone Temperature / Moisture / Humidity Sensor

EA200-12 Enviro Alert 2-Zone Temperature / Moisture / Humidity Sensor

Winland Electronics EnviroAlert® Dual Zone Digital Environmental Monitoring Alarm (EA200-12 & EA200-24)

Monitor two zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor the designated relay for each zone will activate an alarm, dialer, transmitter, etc.



EA200-24 Enviro Alert 2-Zone Temperature / Moisture / Humidity Sensor

EA200-24 Enviro Alert 2-Zone Temperature / Moisture / Humidity Sensor

Winland Electronics EnviroAlert® Dual Zone Digital Environmental Monitoring Alarm (EA200-12 & EA200-24)

Monitor two zones with any combination of a remote temperature, humidity or water sensing probe. If temperatures and humidity deviate from the preset limits or water forms a bridge between the contacts on the WaterBug® sensor the designated relay for each zone will activate an alarm, dialer, transmitter, etc.





Mechanical Temp Alert MTA-1
The professional looking MTA-1 requires no power for operation. Simply set the separately adjustable high and low set points within +32 to +100 deg F (0 to 38 deg C) range. If the monitored temperature rises above the high set point, a dry contact closure output is provided. If the monitored temperature falls below the low set point, a second dry contact closure output is provided.
MTA-1 Mechanical Temp Alert

MTA-1 Mechanical Temp Alert

MTA-1 Mechanical Temp Alert from Winland Electronics

The professional looking MTA-1 requires no power for operation. Simply set the separately adjustable high and low set points within +32 to +100 deg F (0 to 38 deg C) range. If the monitored temperature rises above the high set point, a dry contact closure output is provided. If the monitored temperature falls below the low set point, a second dry contact closure output is provided.






Humid-Alert HA-1
The HA-1 is a stand-alone humidity-monitoring device requiring no power for operation. Simply set the single high or low adjustable set point within 20% to 80% range. If the monitored humidity set point is met or exceeded, a SPDT micro-switch will activate.
HA-1 Humid-Alert

HA-1 Humid-Alert

HA-1 Humid-Alert from Winland Electronics

The HA-1 is a stand-alone humidity-monitoring device requiring no power for operation. Simply set the single high or low adjustable set point within 20% to 80% range. If the monitored humidity set point is met or exceeded, a SPDT micro-switch will activate.






Mechanical Fixed Temp Alert TA-40
The simple low-cost TA-40 requires no power for operation. A mechanically fixed set point allows normally closed contacts to open when the monitored temperature falls below the 39 deg F (4 deg C) set point. This contact output is used to active external low current/voltage alarm
TA-40 Mechanical Fixed Temp Alert

TA-40 Mechanical Fixed Temp Alert

Winland TA-40 Mechanical Fixed Temp Alert

The simple TA-40 Temp switch is the perfect solution for simple low cost protection in homes, mountain cabins, or any unattended building. The unit will activate a hardwire or wireless alarm system if the temperature should fall below 40°F from its fixed internal sensor. The TA-40 provides positive protection and peace-of-mind to residential and business property owners concerned about the risk of frost shattered pipes and the water damage that follows. An added advantage is the unit's compact size, which enables it to be installed in virtually any setting without being noticed. Contacts above 40° F are normally closed and below 40° F are normally open.






Mechanical Temp Alert TA-2HL
The economical TA-2HL requires no power for operation. Simply set the separately adjustable high and low set points within -30 to +130 deg F (-34 to 54 deg C) range. If the monitored temperature rises above the high set point, a dry contact closure output is provided. If the monitored temperature falls below the low set point, a second dry contact closure output is provided.
TA-2HL Mechanical Temp Alert

TA-2HL Mechanical Temp Alert

TA-2HL Mechanical Temp Alert from Winland Electronics

The economical TA-2HL requires no power for operation. Simply set the separately adjustable high and low set points within -30 to +130 deg F (-34 to 54 deg C) range.">






Mechanical Temp Alert TA-1
The economical TA-1 requires no power for operation. Simply set the separately adjustable high and low set points within -30 to +130 deg F (-34 to 54 deg C) range. If the monitored temperature rises above or falls below the set points, a dry contact closure output is provided.
TA-1 Mechanical Temp Alert

TA-1 Mechanical Temp Alert

TA-1 Mechanical Temp Alert from Winland Electronics






Probes & Accessories
The following probes are used with the Enviro Alert series controllers to detect high or low temperature, humidity or water in one or more zones.

1107 Low Temp Sensor with 15 ft Cable

1107 Low Temp Sensor with 15 ft Cable



M001-0082 Remote Probe

M001-0082 Remote Probe

STAINLESS STEEL LOW TEMP THERMISTOR PROBE (-58° TO +158°F)



M-001-0086 Waterproof Low Temp Thermistor Probe (-58 to 158º F)

M-001-0086 Waterproof Low Temp Thermistor Probe (-58 to 158º F)

Winland M-001-0086 Waterproof Low Temp Thermistor Probe (-58 to 158º F)




M-001-0087 Waterproof High Temp Thermistor Probe (32 to 299º F)

M-001-0087 Waterproof High Temp Thermistor Probe (32 to 299º F)

Winland M-001-0087 Waterproof High Temp Thermistor Probe (32 to 299º F)

Features
  • 32º to 299º F (0º to 150º C)
  • Fully submersible waterproof construction
  • For use with EnviroAlert products only



HAIII+ Electronic Humidity Sensor (M-001-0091)

HAIII+ Electronic Humidity Sensor (M-001-0091)

Winland HAIII+ Electronic Humidity Sensor (M-001-0091)

P/N M0010091

Features
  • 5% to 95% RH +/5% Accuracy
  • Wall mount design
  • For use with EnviroAlert products only



M-001-081 SS High Temperature Thermistor Probe (32-299ºF) - Winland Electronics

M-001-081 SS High Temperature Thermistor Probe (32-299ºF)




M-001-082 SS Low Temperature Thermistor Probe (-58 - 158ºF) - Winland Electronics

M-001-082 SS Low Temperature Thermistor Probe (-58 - 158ºF) - Winland Electronics




1106 Winland Standard Temperature Sensor [no cable. not for freezers or coolers] 1106 +32° to +220° F (0° to +105° C)

1106 Winland Standard Temperature Sensor [no cable. not for freezers or coolers] 1106 +32° to +220° F (0° to +105° C)

1106 Winland Standard Temperature Sensor [no cable. not for freezers or coolers]



1111 Wall Transformer

1111 Wall Transformer from Winland Electronics




1175 Remote Annunciator (12 VDC)

1175 Remote Annunciator (12 VDC) from Winland Electronics






Honeywell
Honeywell Temperature Sensors
Honeywell TS300 Dual Temperature Sensor

Honeywell TS300 Dual Temperature Sensor

Ademco TS300 Dual Temperature Sensor

  • Simultaneous operation of local and remote probes
  • Local sensor 32° to 140° F (0° to 60°C) +/-3°F (+/-2.2°C)
  • Remote probe -40° to 140° F (-40° to 60°C) +/-4°F (+/-2.2°C)
  • Programmable hysteresis prevents multiple alarms
  • Output Matrix Mapping provides versatility and flexibility
  • Audible alarm with silence timeout
  • Alarm memory (up to 8 events)



TS300R Remote Temperature Probe - Honeywell

TS300R Remote Temperature Probe - Ademco